SUNSHINE S-918F PLUS 5 in 1 Edge Screen Separator

An edge-screen phone lands on your bench with a cracked display, and the glass sits locked to the frame under factory adhesive. Pry it the wrong way and you tear the flex cable, crack the OLED panel or bend the frame. The Sunshine S-918F Plus 5 in 1 Edge Screen Separator targets exactly this job. One machine takes flat screens and edge screens, so you do not need a separate setup for each display type. What “5 in 1” means on your bench The five functions cover the full screen-removal sequence: heating, separation, glue removal, frame removal and screen removal. You warm the adhesive, hold the display, split the glass from the panel or frame, clear the old glue and lift the screen out, all on the same platform. That sequence matters most in screen refurbishing, where you keep a good OLED or LCD panel and replace only the damaged glass. It also matters when a customer brings a phone with a display problem and you need the screen off cleanly before any deeper repair. Tiltable panel for controlled glue removal The panel tilts left and right. Tilting lets the glue-removal liquid flow toward the left or right frame glue line, exactly where you need it. Sunshine builds the machine so the glue releases from the inside toward the outside. The liquid stays away from the cable. Liquid damage to the flex causes many display problems after a refurbish job, so this layout protects the part you can least afford to ruin.360° rotation without constant repositioning Built-in precision bearings turn the platform through a full 360° smoothly. You rotate the phone to reach each side instead of lifting it, repositioning it and losing your hold. Fewer manual repositions give you steadier hands when you work a separation wire or blade around a curved edge, which is the hardest part of any edge-screen job.Sealed hose, longer pump life The hose uses a fully sealed design. Glass dust, chips and small debris stay out of the machine, which extends the working life of the suction pump and the built-in pump. A busy shop produces glass dust all day, so a sealed hose matters on a machine that runs every day.One machine for flat and curved displays Many separators handle flat screens well and struggle with curved glass. The S-918F Plus covers both on the same platform. You switch between a flat-screen Android, an iPhone and an edge-screen phone without changing machines or rebuilding your setup. For a shop owner, that means one unit on the bench instead of two, and every technician on the team learns one workflow.Where it fits in your repair workflow Screen removal comes first in most phone repairs. A dead phone with a hardware fault, a charging issue, a network issue or a hang on logo usually needs the display off before you reach the motherboard. Once the screen lifts cleanly, the rest of the job moves faster. You can move the board to a PCB holder, inspect the display connector under a microscope, check lines with a multimeter, and handle IC change karna work on your hot air station or soldering station. If you reball a CPU or eMMC, a damaged display flex adds another cost to the job, so a clean separation protects your margin.For display refurbishing, the separator drives the whole process. You separate the broken glass, clean the panel, and prepare it for a new glass lamination. Edge-screen panels cost more than flat ones, and every panel you save instead of scrap adds up over a month in a busy repair shop.Who gains the most Repair shop owners in Pakistan see the value first. Edge-screen phones from Samsung, Huawei and other brands keep growing in the local market, and customers arrive with cracked curved displays every week. Service centers gain a repeatable process for high-volume display work. Screen refurbishing benches gain a machine built around glue removal and frame handling. Technical training institutes gain a clear teaching tool, because students watch the heating, separation and glue-removal stages happen on one platform.Practical tips for better results Heat the display evenly before you start any cut, and give the adhesive time to soften. Hold the phone firmly on the platform so the suction does not shift when you tilt or rotate. Work slowly around the curved corners, since those corners break first. Keep the glue-removal liquid on the frame glue line and away from the cable, and use the left and right tilt to steer it. After separation, inspect the flex connector and the panel edge under your microscope before you assemble the new glass. These habits turn a risky job into a routine one.Power supply The machine runs on AC 110V/220V, so it works on the standard 220V supply in Pakistani workshops without an extra converter.Upgrade path If you currently remove screens with a basic heating plate and manual prying, the S-918F Plus gives you a clear step up. You gain a built-in pump, a tilting panel, smooth rotation and a process built for curved glass. Pair it with a good microscope, a set of PCB holders and your existing hot air station to build a complete display and board repair bench.The Sunshine S-918F Plus 5 in 1 Edge Screen Separator gives your bench one dependable machine for flat and curved screens. It protects the flex cable, keeps your suction system clean, and makes edge-screen separation a controlled job instead of a gamble.